LET'S GET STARTED

Now you've probably heard of a beam antenna, and maybe you've heard of a J-Pole.

But what's a J BEAM?

It's a vertical directional antenna made of 1/2 inch copper pipe and wood or PVC.
It uses a standard J-pole antenna as the driven element and center support, with two parasitic elements-----a reflector and a director, to provide directivity and gain. See J Beam pattern below. It can be built for around RM25.00 and you can use your old Jpole as a basis for the JBeam. You'll probably need to shorten the main 1/2 wave element by 1 to 2 inches, as the reflector and director tend to couple and lower the resonance of your original jpole toward the lower part of the band. See formulas for cutting to your desired frequency of operation or band . A small amount of trimming on the tip of the main active 1/2 wave element may be needed to get the SWR as low as possible. You shouldn't have to adjust the 1/4 wave matching stub, as this is not strongly affected by the parasitic elements.

Design Details and Drawbacks

The element lengths and spacings are a combination of info from the ARRL Antenna Book section on 2 meter Yagi antennas, and from experiments with a field strength meter and different length elements and spacings.

The reflector and director element spacings are equal at 16 inches. Slightly higher gain with reflector spacing at 18 inches from driven element and director spacing of 14 inches can be had but the antenna may tend to lean with unequal spacings if strong mast mounting is not used.

The bandwidth is not as wide as that of the standard jpole by itself. The SWR tends to rise faster toward the ends of the band, but you get an estimated 7dB
gain and 20 dB F/B (front to back ratio).

High wind loading could potentiallly break off the jBeam at the bottom joint
since the entire structure is supported by that point. You may want to reinforce
it.

CONSTRUCTION

The lengths used in these plans are for the upper part of 2 meters and you can use the formulas to design it for your frequency.

1/2 inch copper pipe is used for all elements and standard soldering made with a small blowtorch. A soldering iron is just not hot enough!

Longest element = 58 1/2 inches (add about 2 feet for mast mounting) matching 1/4 wave stub = 20 1/4 inches

(position matching stub toward director for a bit of added gain reflector -
40 inches

director = 32 inches

stub and main element spacing = 3 inches

coax feed point = 3 to 5 inches from bottom

(use hose clamps for feed point coax attachment connections for easy repair/adjustment)

Center boom is 1/2 inch by 1-inch wood or PVC and about 36 inches long

Measurements should be made as close as possible but are not extremly critical!

Element to boom mounting variations depend on your particular situation and construction materials at hand but insure that element centers are at center of boom Use your own imagination! (see pics for better details)

"One fellow built one with five elements-----just cutting the extra directors shorter by eye-----and was able to work a repeater 35 miles away, with a 5-watt HT holding the antenna, from a valley that's hard to get out of with 50 watts and an omnidirectional antenna at 30 feet!"

>FORMULAS<

J Pole Long element (in Inches) = 8568 / F mhz

J pole Stub (in inches) = 2952 / F in mhz

Reflector (in inches) = 5880 / F in mhz

Director (in inches) = 4704 / F in mhz

Spacing (in inches) = 2352 / F in mhz

Some examples for other bands:

224 mhz

DE: 38.25"

STUB: 13.17"

REF : 26.52"

DIR: 21"

SPACING: 10.5"

444 mhz

DE: 19.29"

STUB 6.6"

REF: 13.24"

DIR: 10.59"

"A PICTURE IS WORTH A THOUSAND WORDS"

Here are two thousand words!

Notes: Make
driven element about 2 feet longer at bottom for mast mounting.

Center conductor of coax to longest element, shield to shortest

k-RAMAT atau Koperasi Radio Amatur Malaysia ditubuhkan atas dasar untuk membina satu rangkaian komprehensif peminat radio amatur yang telah sedia ada di Malaysia ini. k-RAMAT juga berfungsi untuk memberi kebajikan kepada semua ahli dalam pelbagai bentuk kelebihan yang akan ditawarkan oleh koperasi k-RAMAT ini. Buat sementara waktu k-RAMAT ini beroperasi di No.22, Jalan BP6/12, Bandar Bukit Puchong, 47100 Puchong, Selangor. Tel: 03-80623370 Fax: 03-80623372. Emel address koperasi.radioham@gmail.com
Maklumat Lanjut ====>> k-RAMAT ( KOPERASI RADIO AMATUR MALAYSIA)

Assalamualaikum & Salam Sejahtera,

Sekadar info:

Keputusan RAE 2008-2 telah pun dikeluarkan oleh pihak MCMC.

Syabas dan tahniah kepada semua yang telah berjaya, dan jangan berputus-asa kepada yang telah gagal dan cuba lagi di masa depan.


Keputusan boleh dilihat disini

RAE 2008-1 (Result)


Perkara-perkara yang perlu dilakukan setelah lulus RAE

1. Tunggu surat pengesahan lulus daripada MCMC
2. Isi Surat Permohonan Callsign
3. Isi Borang permohonan Apparatus Assignment (A.A)
4. Isi Surat Sokongan 9M2
5. Isi Surat Akuan Sumpah


Dan serahkan pada Pejabat MCMC/SKMM yang berhampiran bersama

RM60.00 (yuran pemprosesan)
RM24.00 untuk setahun (maks 5 tahun shj)


Harap maklum..

73